- 相關推薦
思科、華為、H3C常用命令對比大全
路由命令是交換機最基本的命令了，思科、華為、H3C這些網絡設備的命令還是挺多的，不過我們一般用的路由交換機設備都是最簡單的了，先學基本命令，再學其他功能命令。
思科、華為、H3C常用命令對比大全
| CISCO | H3C | HUAWEI | 描述 |
| no | undo | undo | 取消、關閉當前設置 |
| show | display | display | 顯示查看 |
| exit | quit | quit | 退回上級 |
| hostname | sysname | sysname | 設置主機名 |
| en, config terminal | system-view | system-view | 進入全局模式 |
| delete | delete | delete | 刪除文件 |
| reload | reboot | reboot | 重啟 |
| write | save | save | 保存當前配置 |
| username | local-user | local-user | 創建用戶 |
| shutdown | shutdown | shutdown | 禁止、關閉 端口 |
| show version | display version | display version | 顯示當前系統版本 |
| show startup-config | display saved-configuration | display saved-configuration | 查看已保存過的配置 |
| show running-config | display current-configuration | display current-configuration | 顯示當前配置 |
| no debug all | ctrl+d | ctrl+d | 取消所有debug命令 |
| erase startup-config | reset saved-configuration | reset saved-configuration | 刪除配置 |
| end | return | return | 退到用戶視圖 |
| exit | logout | logout | 登出 |
| logging | info-center | info-center | 指定信息中心配置信息 |
| line | user-interface | user-interface | 進入線路配置（用戶接口）模式 |
| start-config | saved-configuration | saved-configuration | 啟動配置 |
| running-config | current-configuration | current-configuration | 當前配置 |
| host | ip host | ip host | host名字和ip地址對應 |
| 交換部分 | |||
| enable password | set authentication password simple | set authentication password simple | 配置明文密碼 |
| interface type/number | interface type/number | interface type/number | 進入接口 |
| interface vlan 1 | interface vlan 1 | interface vlan 1 | 進入vlan配置vlan管理地址 |
| interface rang | interface ethID to ID | interface ethID to ID | 定議多個端口的組 |
| enabl esecret | super password | super password | 設置特權口令 |
| duplex (half|full|auto) | duplex (half|full|auto) | duplex (half|full|auto) | 配置接口狀態 |
| speed (10/100/1000) | speed (10/100/1000) | speed (10/100/1000) | 配置端口速率 |
| switchport mode trunk | port link-type trunk | port link-type trunk | 配置trunk |
| vlan ID /no vlan ID | vlan batch ID /undo vlan batch ID | vlan batch ID /undo vlan batch ID | 添加、刪除vlan |
| switchport access vlan | port default vlan ID | port acces vlan ID | 將端口接入vlan |
| show interface | display interface | display interface | 查看接口 |
| show vlan ID | display vlan ID | display vlan ID | 查看vlan |
| encapsulation | link-protocol | link-protocol | 封裝協議 |
| channel-group 1 mode on | port link-aggregation group 1 | port link-aggregation group 1 | 鏈路聚合 |
| ip routing | 默認開啟 | 默認開啟 | 開啟三層交換的路由功能 |
| no switchport | 不支持 | 不支持 | 開啟接口三層功能 |
| vtp domain | GVRP | GVRP | 對跨以太網交換機的VLAN進行動態注冊和刪除 |
| spanning-tree vlan ID root primary | stp instance id root primary | stp instance id root primary | stp配置根網橋 |
| spanning-tree vlan ID priority | stp primary vlaue | stp primary vlaue | 配置網橋優先級 |
| show spanning-tree | dis stp brief | dis stp brief | 查看STP配置 |
| 路由部分 | |||
| ip route 0.0.0.0 0.0.0.0 | ip route-static 0.0.0.0 0.0.0.0 | ip route-static 0.0.0.0 0.0.0.0 | 配置默認路由 |
| ip route 目標網段+掩碼 下一跳 | ip route-static 目標網段+掩碼 下一跳 | ip route-static 目標網段+掩碼 下一跳 | 配置靜態路由 |
| show ip route | display ip routing-table | display ip routing-table | 查看路由表 |
| router rip /network 網段 | rip /network 網段 | rip /network 網段 | 啟用rip、并宣告網段 |
| router ospf | ospf | ospf | 啟用ospf |
| network ip 反碼 area <area-id> | area <area-id> | area <area-id> | 配置OSPF區域 |
| no auto-summary | rip split-horizon | rip split-horizon | 配置RIP V2水平分割 |
| show ip protocol | display ip protocol | display ip protocol | 查看路由協議 |
| access-list 1-99 permit/deny IP |
rule id permit source IP |
rule id permit source IP | 標準訪問控制列表 |
| access-list 100-199 permit/deny protocol source IP+反碼 destination IP+反碼 operator operan | rule {normal|special}{permit|deny}{tcp|udp}source {<ip wild>|any}destination <ip wild>|any}[operate] | rule {normal|special}{permit|deny}{tcp|udp}source {<ip wild>|any}destination <ip wild>|any}[operate] | 擴展訪問控制列表 |
| standby group-number ip virtual-ip | vrrp vrid number virtual-ip | vrrp vrid number virtual-ip | 配置HSRP組 |
| standby group-number priority | vrrp vrid number priority | vrrp vrid number priority | 配置HSRP優先級 |
| standby group-number preempt | vrrp vrid number preempt-mode | vrrp vrid number preempt-mode | 配置HSRP占先權 |
| standby group-number track | 配置端口跟蹤 | ||
| ip nat inside source static | nat server global <ip> [port] inside <ip> port [protocol] | nat server global <ip> [port] inside <ip> port [protocol] | 配置靜態地址轉換 |
更多相關文章推薦：
6.華為上機試題匯總
【思科、華為、H3C常用命令對比】相關文章：
思科與H3C配置命令對比10-13
華為交換機常用命令匯總02-26
華為交換機常用命令大全01-22
H3C交換機常用命令注釋12-06
H3C交換機常用命令大全07-13
華為交換機常用命令2016最新08-12
思科認證輔導：三種網絡交換技術全面對比07-28
思科認證詳解和思科未來05-22