抓斗起重機運用先進的可編程控制技術
Abstract
The paper mainly researches the application of advanced PLC (Programmable Logic Controller), transducer, and absolute encoder in the grab bucket crane, which takes the place of the traditional mode of the electric control and aims to improve the work efficiency of grab bucket crane and decrease its failure rate. These applications will bring a lot of advantages, such as lower maintenance costs, lower workload of maintenance, and easily to be manipulated etc. It is also achieved to be semi-automatic operation to reduce the risk of man-made operation accident with the effects of reliable running and energy-saving.
The paper primarily focuses on the principle of automatic open / close grab of grab bucket crane and proposes the principle and physical significance of the moving coordinate method. It is practical that the applied absolute encoder automatically follows the lifting and landing of grab bucket and measures the length difference value of steel wire rope to achieve the function of its automatic opening or closing and stable grabbing. According to the usual failures during the practical application of grab bucket crane, the failure display is also developed to be applied to the crane.
The paper consists of four parts:
The first part (Chapter one: Introduction) mainly describes the working principle of grab bucket crane, focusing on the problems of crane controlled in the traditional method, and further exploring the feasibility for intelligent implementation of grab bucket crane.
The second part (Chapter 2, 3, 4) describes the configuration and functional principles of PLC, transducer and encoder. It also makes a theoretical analysis for the selection of PLC, transducer and encoder, which lays a theoretical foundation for the realization of the intelligent operation of grab bucket crane in the following chapter.
The third part (Chapter 5) researches the specific schemes for intelligent implementation of grab bucket crane, such as heavy trolley, light trolley, controller configuration, PLC, transducer, electric connection of absolute encoder, working principle etc. It explicitly explained the principle of automatic open/ close grabbing of crane and the implementation of stable grabbing. It also introduces the realization principle to substitute the limit position of ascending with the utility of encoder.
The fourth part (Chapter 6) mainly introduces soft structure of intelligent operation and PLC configuration of gab bucket crane. The software program of heavy trolley, light trolley, and switching & hoisting mechanism is also composed in the paper.
In the end, it is summarized for the whole research and makes an outlook for the future research.
Key words: crane, PLC, transducer, absolute encoder, automatic opening /closing grab failure display.
摘 要
本論文主要研究抓斗起重機運用先進的可編程控制技術、變頻器和絕對值編碼器，取代傳統的電氣控制方式，提高抓斗起重機的工作效率，減小抓斗起重機的故障率，降低維修費用，使維修工作量大大減少，操作變得簡單，可以實現半自動化操作，減少人為的'操作事故，運行可靠，具有節能效果。
本論文著重研究抓斗起重機自動開閉斗的原理，提出游動坐標法的原理及物理意義，利用絕對值編碼器自動跟蹤檢測抓斗起升、開閉鋼絲繩的長度差值，實現自動開閉、沉抓的功能，具有實用價值。并根據抓斗起重機實際運用中經常出現的故障，開發出故障顯示功能。
本論文分成四個部分：
第一部分（第一章）緒論部分主要對抓斗起重機工作原理作了介紹，著重介紹了抓斗起重機傳統控制方式存在的問題，進而探討了實現抓斗起重機智能操作的研究可能性和研究意義。
第二部分（第二、三、四章）分別對可編程控制器（PLC），變頻器、絕對值編碼器的組成、功能各原理作了介紹，以及PLC、變頻器、編碼器的選型作了理論上的分析，為下文抓斗起重機智能化控制的實現打下了理論基礎。
第三部分(第五章)研究抓斗起重機智能控制的具體實現方案，大車、小車，起升開閉機構PLC、變頻器、絕對值編碼器的電氣連接、工作原理。特別詳細闡述了抓斗實現自動開閉斗的原理，以及抓斗自動沉抓功能的實現。還介紹了用編碼器取代上升極限位的實現原理。
第四部分（第六章）主要介紹抓斗起重機智能控制的軟件結構，PLC組態、還詳細寫出大車、小車、起升開閉機構的軟件程序。
最后對整個研究作一總結，并且對今后的研究方向作了展望
關鍵詞：起重機、可編程控制器、變頻器、絕對值編碼器、自動開閉斗、故障顯示
【抓斗起重機運用先進的可編程控制技術】相關文章：